Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Cellulose or fibreglass?

Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

Attic Insulation Bellevue Edmonton | Attic Top-Up

Attic top-ups in Bellevue that hold their depth

Attics in Bellevue lose depth over time — insulation settles, someone crawls through it for a wiring job, and the corners near the eaves are usually thin to begin with. A top-up is only worth doing if the baffles are clear and the ceiling below is sealed, so that is what we check before quoting.

Baffles kept clear so the soffit vents still breathe
Blown-in loose-fill to the depth your permit specifies
Existing insulation levelled before the top-up
Depth markers left in place so the result is verifiable
Air sealing at pot lights, top plates and the attic hatch
Attic hatch insulated and weatherstripped

Attics over additions and vaulted areas

The awkward spaces

An Bellevue addition often has a shallow attic, a cathedral section or a knee wall, and those areas are where insulation is thinnest and access is worst.

Why they matter disproportionately

They are frequently the coldest rooms in the house, and they are the parts a general top-up misses because the blower cannot reach them. We look at them specifically rather than quoting an average depth across the whole ceiling.

Bellevue drywall in context

About Bellevue

One of the City's smaller neighbourhoods, Bellevue was developed prior to 1950.

What we see in Bellevue

In Bellevue the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Bellevue ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Bellevue attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

Adding to what is already there

You rarely start empty

Most Bellevue attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

Why air sealing comes before insulation in Bellevue

Insulation does not stop air

Batt and loose-fill slow heat transfer; neither stops air movement. In an Bellevue attic warm moist household air rises through pot lights, top plates and the hatch, passes straight through the insulation and condenses when it hits the cold deck.

What that looks like later

Frost on the underside of the sheathing in February, then staining on the ceiling in spring. Sealing the penetrations first is the difference between insulation that works and insulation that becomes the problem.

How it works

Simple, clean, on schedule — Attic Insulation in Bellevue Edmonton

Free quote

We come out to your Bellevue Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Bellevue Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Bellevue Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bellevue Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Bellevue Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Bellevue Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Bellevue Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Bellevue Edmonton

Attic Insulation Bellevue Edmonton: your questions answered

Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
Cellulose or fibreglass?: Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Bellevue Edmonton

Attic top-ups in Bellevue that hold their depth