Can you blow insulation over my pot lights?

Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.

Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

How much insulation should my Belle Rive attic have?

The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.

Cellulose or fibreglass?

Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Attic Insulation Belle Rive Edmonton | Attic Top-Up

Attic insulation in Belle Rive: air seal first, then blow

The most common mistake in an Belle Rive attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Air sealing at pot lights, top plates and the attic hatch
Baffles kept clear so the soffit vents still breathe
Attic hatch insulated and weatherstripped
Blown-in loose-fill to the depth your permit specifies
Depth markers left in place so the result is verifiable
Existing insulation levelled before the top-up

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Belle Rive attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

The attic hatch nobody insulates

A hole in the ceiling

An uninsulated, unsealed hatch is a direct opening between the heated house and a cold attic, and it is often the single worst detail in an otherwise good Belle Rive ceiling.

Simple fix

An insulated cover with weatherstripping and a dam around the opening so blown insulation does not spill through when it is opened.

Why air sealing comes before insulation in Belle Rive

Insulation does not stop air

Batt and loose-fill slow heat transfer; neither stops air movement. In an Belle Rive attic warm moist household air rises through pot lights, top plates and the hatch, passes straight through the insulation and condenses when it hits the cold deck.

What that looks like later

Frost on the underside of the sheathing in February, then staining on the ceiling in spring. Sealing the penetrations first is the difference between insulation that works and insulation that becomes the problem.

Cellulose against fibreglass in an Belle Rive attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

Storage in the attic and the insulation you lose

Boards over joists compress everything

Where a Belle Rive homeowner has laid plywood across the joists for storage, the insulation beneath is squashed to joist depth. That strip performs at a fraction of the rest of the attic.

Options

Either the storage area is raised on a platform above the finished insulation depth, or it is accepted as a deliberately weaker zone kept as small as possible. What does not work is topping up around it and pretending the platform is not there.

Adding to what is already there

You rarely start empty

Most Belle Rive attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

How it works

Simple, clean, on schedule — Attic Insulation in Belle Rive Edmonton

Free quote

We come out to your Belle Rive Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Belle Rive Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Belle Rive Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Belle Rive Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Belle Rive Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Belle Rive Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Belle Rive Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Belle Rive Edmonton

Attic Insulation Belle Rive Edmonton: your questions answered

Can you blow insulation over my pot lights?: Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.
Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.
How much insulation should my Belle Rive attic have?: The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
Cellulose or fibreglass?: Both work when installed to depth with the ceiling sealed underneath. Cellulose is denser and resists air movement better; fibreglass is lighter and settles less. We pick based on what is already up there and tell you why.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Belle Rive Edmonton

Attic insulation in Belle Rive: air seal first, then blow