Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

How do I know I got the depth I paid for?

We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Attic Insulation Beaumont | Attic Top-Up

Attic top-ups in Beaumont that hold their depth

The most common mistake in an Beaumont attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Blown-in loose-fill to the depth your permit specifies
Baffles kept clear so the soffit vents still breathe
Air sealing at pot lights, top plates and the attic hatch
Depth markers left in place so the result is verifiable
Existing insulation levelled before the top-up
Attic hatch insulated and weatherstripped

The attic hatch, which everybody forgets

A hole in the ceiling

The hatch in an Beaumont home is often an uninsulated panel sitting in a frame with no weatherstrip. It is a direct opening between the house and a space that is at outdoor temperature.

What we do

The hatch gets insulated on its back face and weatherstripped so it seals when closed. It is a small job that shows up disproportionately in comfort, and it is the first place we look when someone says the hallway is cold.

Adding to what is already there

You rarely start empty

Most Beaumont attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

Cellulose against fibreglass in an Beaumont attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

Depth, and how to check we delivered it

Verifiable rather than assumed

Blown insulation settles, and depth is easy to claim and hard to check once the hatch is closed. We leave depth markers through the Beaumont attic so the installed depth can be read off later by anyone.

Even coverage

Depth is also an average — a deep drift in the middle and thin corners is not the same as an even blanket. Coverage to the edges is what actually reduces heat loss.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Beaumont attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

The attic hatch nobody insulates

A hole in the ceiling

An uninsulated, unsealed hatch is a direct opening between the heated house and a cold attic, and it is often the single worst detail in an otherwise good Beaumont ceiling.

Simple fix

An insulated cover with weatherstripping and a dam around the opening so blown insulation does not spill through when it is opened.

How it works

Simple, clean, on schedule — Attic Insulation in Beaumont

Free quote

We come out to your Beaumont property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Beaumont starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Beaumont. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Beaumont home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Beaumont. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Beaumont Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Beaumont trusts for repair, restoration and finishing — rated on Google by Beaumont homeowners.

Read the reviews, or leave your own after your attic insulation project in Beaumont.

Read our reviews on Google

FAQ — Attic Insulation Beaumont

Attic Insulation Beaumont: your questions answered

Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
How do I know I got the depth I paid for?: We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Beaumont

Attic top-ups in Beaumont that hold their depth