How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

Why does my Beacon Heights attic frost up in winter?

Almost always warm moist air leaking up from the house through pot lights, top plates or the hatch, then condensing on cold sheathing. More insulation on its own does not fix it — the leaks have to be sealed first.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

How much insulation should my Beacon Heights attic have?

The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.

Can you blow insulation over my pot lights?

Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.

Attic Insulation Beacon Heights Edmonton | Attic Top-Up

Attic top-ups in Beacon Heights that hold their depth

Attics in Beacon Heights lose depth over time — insulation settles, someone crawls through it for a wiring job, and the corners near the eaves are usually thin to begin with. A top-up is only worth doing if the baffles are clear and the ceiling below is sealed, so that is what we check before quoting.

Attic hatch insulated and weatherstripped
Blown-in loose-fill to the depth your permit specifies
Air sealing at pot lights, top plates and the attic hatch
Existing insulation levelled before the top-up
Baffles kept clear so the soffit vents still breathe
Depth markers left in place so the result is verifiable

Adding to what is already there

You rarely start empty

Most Beacon Heights attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

Beacon Heights drywall in context

About Beacon Heights

Beacon Heights was one neighbourhood that made up the area called Beverly.

What we see in Beacon Heights

In Beacon Heights the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Cellulose against fibreglass in an Beacon Heights attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Beacon Heights attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Storage in the attic

An honest trade-off

Boards laid over the joists in an Beacon Heights attic compress the insulation beneath them and create a thin band right through the middle of the ceiling.

What we suggest

A raised platform over a limited area if storage is genuinely needed, so the insulation depth continues underneath it. Or accepting that a full-depth attic is not also a storage room.

Storage in the attic and the insulation you lose

Boards over joists compress everything

Where a Beacon Heights homeowner has laid plywood across the joists for storage, the insulation beneath is squashed to joist depth. That strip performs at a fraction of the rest of the attic.

Options

Either the storage area is raised on a platform above the finished insulation depth, or it is accepted as a deliberately weaker zone kept as small as possible. What does not work is topping up around it and pretending the platform is not there.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Beacon Heights attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

How it works

Simple, clean, on schedule — Attic Insulation in Beacon Heights Edmonton

Free quote

We come out to your Beacon Heights Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Beacon Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Beacon Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Beacon Heights Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Beacon Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Beacon Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Beacon Heights Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Beacon Heights Edmonton

Attic Insulation Beacon Heights Edmonton: your questions answered

How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
Why does my Beacon Heights attic frost up in winter?: Almost always warm moist air leaking up from the house through pot lights, top plates or the hatch, then condensing on cold sheathing. More insulation on its own does not fix it — the leaks have to be sealed first.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.
How much insulation should my Beacon Heights attic have?: The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.
Can you blow insulation over my pot lights?: Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Beacon Heights Edmonton

Attic top-ups in Beacon Heights that hold their depth