Why is the area above my exterior walls always cold?

Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

Can you blow insulation over my pot lights?

Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.

Will insulating my attic stop the ice at my eaves?

Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.

Attic Insulation Allard Edmonton | Attic Top-Up

Blown-in attic insulation in Allard, sealed before it is filled

The most common mistake in an Allard attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Existing insulation levelled before the top-up
Air sealing at pot lights, top plates and the attic hatch
Attic hatch insulated and weatherstripped
Depth markers left in place so the result is verifiable
Baffles kept clear so the soffit vents still breathe
Blown-in loose-fill to the depth your permit specifies

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Allard attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Allard attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Depth, and how to check we delivered it

Verifiable rather than assumed

Blown insulation settles, and depth is easy to claim and hard to check once the hatch is closed. We leave depth markers through the Allard attic so the installed depth can be read off later by anyone.

Even coverage

Depth is also an average — a deep drift in the middle and thin corners is not the same as an even blanket. Coverage to the edges is what actually reduces heat loss.

The attic hatch, which everybody forgets

A hole in the ceiling

The hatch in an Allard home is often an uninsulated panel sitting in a frame with no weatherstrip. It is a direct opening between the house and a space that is at outdoor temperature.

What we do

The hatch gets insulated on its back face and weatherstripped so it seals when closed. It is a small job that shows up disproportionately in comfort, and it is the first place we look when someone says the hallway is cold.

Cellulose against fibreglass in an Allard attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

The eaves are where it goes thin

Geometry works against you

The roof meets the wall at the lowest point in the attic, so there is least room for insulation exactly where the wall below needs it most.

What it needs

Baffles that hold the insulation back from the soffit vents while still letting depth carry out over the wall plate. Skipping them in an Allard attic either blocks the venting or leaves a cold band above every exterior wall.

How it works

Simple, clean, on schedule — Attic Insulation in Allard Edmonton

Free quote

We come out to your Allard Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Allard Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Allard Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Allard Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Allard Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Allard Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Allard Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Allard Edmonton

Attic Insulation Allard Edmonton: your questions answered

Why is the area above my exterior walls always cold?: Geometry. The roof meets the wall at the lowest point in the attic, so there is least room exactly where it is needed most. Baffles hold insulation back from the soffit vents while letting depth carry over the wall plate.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
Can you blow insulation over my pot lights?: Only if they are rated for contact with insulation. Older fixtures need clearance and have to be boxed or replaced. Either way they are significant air leaks, so they get sealed first.
Will insulating my attic stop the ice at my eaves?: Often it helps a great deal, because ice damming is usually escaping heat melting snow that then refreezes over the cold overhang. Air sealing plus even coverage to the eaves lowers the deck temperature, which is the actual cause.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Allard Edmonton

Blown-in attic insulation in Allard, sealed before it is filled