Will this pass inspection?

It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.

Why is there staining around my window reveals?

Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Westwood walls, and it stays invisible until the damage shows.

Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Can you install the barrier if someone else did the insulation?

Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Vapour Barrier Installation Westwood

Vapour barrier details in Westwood that pass inspection

A vapour barrier only works as a continuous plane. In Westwood the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Rim joists air-sealed before insulating
Left ready for inspection before boarding
Poly on the warm side of the insulation
Seams lapped at framing and sealed, not just taped
Electrical boxes poly-hatted and sealed
Window and door returns detailed properly

Windows, doors and the returns around them

Where the detail gets fiddly

The return between a window frame and the wall in Westwood is awkward, tight, and often left as a torn edge tucked behind trim.

Why it matters

It is also a cold junction where condensation shows first, usually as staining or mould at the reveal. The poly is cut to fit, sealed to the frame and supported, rather than folded and hoped for.

Westwood drywall in context

About Westwood

The character of Westwood has changed considerably in the second half of the 20th century.

What we see in Westwood

In Westwood the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

The rim joist and the bottom plate

Two cold junctions

In an Westwood basement the rim joist and the bottom plate against concrete are where warm air meets cold most directly. Both need sealing before insulation, not after.

Sequencing

Once the insulation and poly are on, neither can be reached without pulling the wall apart. We deal with them first, and we would rather flag a problem there at the quote than discover it behind a finished wall.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Westwood are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Why the warm side, and why only one

Which way the moisture moves

Through an Westwood winter, warm humid indoor air pushes outward through the assembly. A vapour barrier on the warm side stops that moisture before it reaches a cold surface where it can condense.

Two barriers is worse than one

A second barrier on the cold side traps moisture between the two with no direction to dry. It is a genuine mistake we still find in renovated walls, and it is invisible until the damage shows.

Electrical boxes, the usual failure point

A hole in the plane

Every outlet and switch in an Westwood exterior wall is a cut in the poly. Left unsealed it is a direct path for moist air into the cavity, and the boxes are usually the coldest spot on the wall.

Poly hats and sealant

Boxes get a poly hat or an air-sealed box, and the poly is sealed to it rather than simply cut around. It is a small detail repeated dozens of times, which is exactly why it gets skipped.

Seams belong on framing

Not floating in a bay

A lap sealed in the middle of a cavity has nothing solid behind it. Any movement or pressure opens it, and it cannot be inspected properly.

How we run it

Sheets are sized so seams land on a stud or plate, lapped, and sealed against solid backing. It uses slightly more material and it is the difference between a barrier that holds and one that is only continuous on the day it was installed.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Westwood

Free quote

We come out to your Westwood property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Westwood starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Westwood. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Westwood home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Westwood. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Westwood trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Westwood.

Read our reviews on Google

FAQ — Vapour Barrier Installation Westwood