Do you hang the ceiling board first?

Yes, always. Ceiling board goes up before wall board on every job in Wellington. The Wellington ceiling board is carried in part by the wall board butting under it. In Wellington, reversing the boarding order leaves ceiling joints unsupported and prone to cracking. No Wellington wall board goes up before the ceiling is complete.

Do you board for legal suites in Edmonton?

Yes, and we know the spec. A legal secondary suite in Edmonton requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, STC soundproof board on party walls, and moisture-resistant in all wet areas. We board to that spec so the suite passes inspection.

For Wellington exterior basement walls, what board do you use?

In Wellington, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Wellington home.

How long does drywall installation take in an Wellington home?

Timeline depends on scope. We give you a specific timeline at the on-site quote. Most single-room or single-area jobs in Wellington are complete in one to two days. Larger basement or whole-home jobs take longer and are scoped precisely before we start.

Can the taping crew start right after you board an Wellington home?

Yes — we hang board with seams on framing, correct screw pattern and plumb walls, so a taper (or we ourselves) can start the very next day in Wellington.

What board do you use for exterior basement walls in Wellington?

Moisture-resistant board covers the Wellington foundation walls and the plumbing and laundry zones. Standard 1/2” board on dry Wellington interior walls. The Wellington suite build: fire-rated 5/8” Type X ceiling, soundproofed party walls. We lock the Wellington board spec per surface at quote time.

Drywall Installation Wellington | New Board

Drywall installation in Wellington — hung straight, screwed off right

The Wellington finish is only as good as the boarding under it. We board Wellington level with proper screws, framed seams and tidy cuts around corners and mechanical. Wellington is a higher-end Northwest community where boarding quality is expected to be consistent with the quality of the rest of the home. We cover Wellington, Albany, Athlone, Baranow and the surrounding area, 7 days a week.

No rework in Wellington: tape-ready boarding when we go
Left ready for taper — no rework needed
Wellington boarding left tape-ready, no rework for the finishers
Wellington basements boarded in order: ceiling, then walls
No rework in Wellington — the board is ready for tape when we go
Fire-rated plus soundproof board on Wellington suite separations
STC soundproof board on party walls for legal suites

Drywall board types for Wellington homes

Standard board for most walls

Standard 1/2-inch drywall is correct for most interior walls and ceilings in Wellington away from moisture exposure.

Moisture-resistant, fire-rated and soundproof where the spec matters

Exterior basement walls and wet areas need moisture-resistant board; legal suite ceilings need fire-rated board; party walls need soundproof board. We specify the right product for every Wellington surface before we pull the first sheet.

Drywall Installation work we do in Wellington

Renovation boarding in 1960s and 1970s Wellington homes

The most common drywall installation call from Wellington is renovation work. Walls come down for a kitchen open-up, a bathroom move or a structural change, and new board goes up on the exposed framing. Wellington homes from this era often have original plaster or early drywall that does not match modern board thickness — we assess the framing and select the right board thickness so the surface is consistent.

Bathroom and wet-area boarding in Wellington — moisture-resistant board

Bathroom renovations in Wellington homes require moisture-resistant board behind tile and around any plumbing chase. We hang moisture-resistant board properly so the tile substrate is solid and the installation holds for the long term.

Why Wellington homeowners trust Emplastrum for drywall installation

Boarding done right means the finish can be done right in Wellington

The quality of a Level 4 wall finish starts with the boarding behind it. Un-level Wellington board, mid-field seams or wide screw spacing all make trouble for the finishers. We board every Wellington job the way a taping specialist would want it boarded — because we are the taping specialist. When we finish the boarding, we can finish the taping to Level 4 without fighting the installation underneath.

Fixed price, same-day reply, all four Edmonton quadrants, Edmonton, Albany, Athlone, Baranow and Edmonton

We cover all four Edmonton quadrants, Edmonton, Albany, Athlone, Baranow and Edmonton, 7 days a week — Wellington, Albany, Athlone, Baranow and every community in between. Your Wellington quote is free and the price fixed — it holds when we arrive.

Our drywall installation process in Wellington, step by step

Ceiling board first — always — in Wellington homes

Every boarding job in Wellington starts with the ceiling. Ceiling board goes up before the walls in Wellington because the wall board butts up under the ceiling board and helps support it. Skipping that sequence means the Wellington ceiling joints carry their own weight unsupported and are more likely to crack. We do not start Wellington walls until the ceiling is done. It is a small thing that makes a significant difference in long-term performance.

Wall boarding, screw pattern and joint placement in Wellington

Wall board goes up with the correct screw pattern — every 12 inches on the field, every 8 inches at the perimeter. All Wellington seams land on framing, not between studs. Inside and outside Wellington corners are clean and square. Wellington board does not run past window and door frames. When the boarding is done in an Wellington home, every surface is at the right plane and the taping crew can go straight to work.

Drywall board types used in Wellington homes

Standard 1/2” drywall — the right choice for most Wellington walls

Standard 1/2” drywall is correct for interior walls and ceilings in Wellington homes away from moisture exposure. It is the most common board we install, finishes the same as the rest of the house and is what most Wellington walls and ceilings should be. Most interior walls and ceilings in Wellington homes use standard 1/2” board.

Moisture-resistant, fire-rated and soundproof — where spec matters in Wellington

Exterior basement walls in Wellington homes need moisture-resistant board. Wellington wet rooms — bath and laundry — get moisture board throughout. In Wellington, suite ceilings run 5/8” Type X fire-rated board. The Wellington suite party wall is built with STC soundproof board. Correct board per Wellington surface, chosen at the quote, keeps inspection clean.

Drywall installation work we do in Wellington

Full basement boarding in Wellington homes

The most common boarding call in Wellington is full basement installation. The builder framed the space; the homeowner is ready to finish it. We hang the ceiling board first — always — then the walls, with moisture-resistant board on all exterior foundation walls. We use the correct screw pattern, land all seams on framing, and cut around mechanical chases and bulkheads cleanly. When the boarding crew leaves an Wellington basement, the taping crew can start without rework.

Legal suite partition boarding in Wellington

Secondary suite additions in Wellington homes require the right board on every surface: 5/8” Type X fire-rated on the ceiling between the suite and the main floor, STC soundproof board on party walls, moisture-resistant in bathrooms and laundry. We board to the Edmonton secondary suite spec so the installation passes inspection without a callback.

How it works

Simple, clean, on schedule — Drywall Installation in Wellington

Free quote

We come out to your Wellington property, take a real look at the drywall installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall installation quote in Wellington starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall installation in Wellington. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Wellington home while we finish the drywall installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall installation with us and you're happy with the result in Wellington. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall installation contractor Wellington trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall installation project in Wellington.

Read our reviews on Google

FAQ — Drywall Installation Wellington

Drywall Installation Wellington: your questions answered

Do you hang the ceiling board first?: Yes, always. Ceiling board goes up before wall board on every job in Wellington. The Wellington ceiling board is carried in part by the wall board butting under it. In Wellington, reversing the boarding order leaves ceiling joints unsupported and prone to cracking. No Wellington wall board goes up before the ceiling is complete.
Do you board for legal suites in Edmonton?: Yes, and we know the spec. A legal secondary suite in Edmonton requires 5/8” Type X fire-rated board on the ceiling separating the suite from the floor above, STC soundproof board on party walls, and moisture-resistant in all wet areas. We board to that spec so the suite passes inspection.
For Wellington exterior basement walls, what board do you use?: In Wellington, exterior foundation walls and plumbing or laundry areas take moisture-resistant board. Standard 1/2-inch board for interior walls away from moisture in your Wellington home.
How long does drywall installation take in an Wellington home?: Timeline depends on scope. We give you a specific timeline at the on-site quote. Most single-room or single-area jobs in Wellington are complete in one to two days. Larger basement or whole-home jobs take longer and are scoped precisely before we start.
Can the taping crew start right after you board an Wellington home?: Yes — we hang board with seams on framing, correct screw pattern and plumb walls, so a taper (or we ourselves) can start the very next day in Wellington.
What board do you use for exterior basement walls in Wellington?: Moisture-resistant board covers the Wellington foundation walls and the plumbing and laundry zones. Standard 1/2” board on dry Wellington interior walls. The Wellington suite build: fire-rated 5/8” Type X ceiling, soundproofed party walls. We lock the Wellington board spec per surface at quote time.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paint

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat). Confirm quantities before buying.

Rather we handle it? Get a free estimate →

Drywall Installation Wellington

Drywall installation in Wellington — hung straight, screwed off right