Do you install the vapour barrier as well?

Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.

Does it matter if the batt is squashed in a bit?

Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Caernarvon bays and cut to fit rather than forcing a standard batt in.

Should I use mineral wool or fibreglass?

Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.

What about the wiring in the wall?

The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.

Can you insulate my finished walls without removing the drywall?

Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.

Why is my Caernarvon basement cold along the floor edge?

Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Batt Insulation Caernarvon | Batt Insulation

Mineral wool and fibreglass batts in Caernarvon walls and ceilings

A batt only performs if it fills the cavity completely and is not squashed. In Caernarvon the two things that ruin it are compression — jamming a wider batt into a narrow bay — and gaps around wiring and boxes, where the insulation is stuffed behind rather than split around.

Split and fitted around wiring and electrical boxes
Mineral wool where fire or sound performance matters
Rim joists insulated and air-sealed
Vapour control detailed before the board goes on
Odd bays cut to fit rather than packed
Batts friction-fit to full cavity width, not compressed

Vapour control, and why the order matters

Warm side, always

In Caernarvon the vapour barrier goes on the warm side of the insulation. Putting it in the wrong place, or having two of them, traps moisture inside the assembly where it cannot dry.

Sequencing

Insulation is completed and inspected before the barrier goes on, and the barrier is sealed at penetrations before boarding. Once drywall is up, none of this can be corrected without taking the wall apart again.

Caernarvon drywall in context

About Caernarvon

One of the Castle Downs subdivisions, Caernarvon is named for a castle in Wales.

What we see in Caernarvon

In Caernarvon the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Insulating an existing Caernarvon wall without opening it

The honest limits

Batts need an open cavity. If a Caernarvon wall is finished and staying finished, batts are not the product — that is a job for a blown-in or injected material, or for adding insulation on the room side.

What we say

We would rather tell you batts are the wrong answer for a closed wall than sell you a partial job. Where the wall is already open for other work, that is the moment to insulate properly.

Compression is the most common Caernarvon mistake

A squashed batt is a weaker batt

Batt insulation works because of the still air trapped in it. Compress it into a narrower bay and you lose a meaningful share of its performance while paying for the full product.

The fix is measurement

Caernarvon framing is not always at a standard spacing, especially in older homes and renovations. We measure the bays and cut to fit rather than forcing a standard batt into a non-standard cavity.

Wiring, boxes and the gaps behind them

Where the cold gets in

The fastest way to ruin a wall in Caernarvon is to stuff the batt behind the wiring and the electrical boxes. It leaves an uninsulated void exactly where there is already a hole in the vapour barrier.

Split, do not stuff

The batt is split so half sits behind the cable and half in front, and it is cut around boxes rather than compressed past them. It is slower and it is the difference between a wall that performs and one that only looks insulated.

Mineral wool against fibreglass in Caernarvon

Different tools

Fibreglass batts are the common choice and perform well when fitted properly. Mineral wool is denser, holds its shape better in a cavity, handles fire differently and performs noticeably better for sound.

Where we would spend the difference

Party walls, bedrooms, mechanical rooms and any assembly where sound or fire matters. For an ordinary interior partition in Caernarvon, fibreglass fitted well beats mineral wool fitted badly.

Rim joists, the coldest part of a Caernarvon basement

Small area, large loss

The rim joist is the band of framing where the floor meets the foundation. It is thin, it is directly exposed to outside, and in most Caernarvon basements it is either bare or has a batt tucked loosely against it.

Air sealing first

A batt alone against a rim joist can trap moist air against a cold surface. The joint gets sealed first, then insulated, so warm household air is not reaching the cold band behind the insulation.

How it works

Simple, clean, on schedule — Batt Insulation in Caernarvon

Free quote

We come out to your Caernarvon property, take a real look at the batt insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every batt insulation quote in Caernarvon starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the batt insulation in Caernarvon. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Caernarvon home while we finish the batt insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished batt insulation with us and you're happy with the result in Caernarvon. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the batt insulation contractor Caernarvon trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your batt insulation project in Caernarvon.

Read our reviews on Google

FAQ — Batt Insulation Caernarvon

Batt Insulation Caernarvon: your questions answered

Do you install the vapour barrier as well?: Yes, and the order matters. Insulation is completed first, the barrier goes on the warm side and is sealed at penetrations before boarding. None of it can be corrected once the drywall is up.
Does it matter if the batt is squashed in a bit?: Yes, more than most people expect. Batts work through trapped still air, so compressing one into a narrow bay costs a real share of its performance. We measure the Caernarvon bays and cut to fit rather than forcing a standard batt in.
Should I use mineral wool or fibreglass?: Fibreglass fitted well beats mineral wool fitted badly for an ordinary partition. Mineral wool is worth the difference on party walls, bedrooms and anywhere sound or fire performance matters — it is denser and holds its shape in the cavity.
What about the wiring in the wall?: The batt gets split so part sits behind the cable and part in front, and it is cut around boxes. Stuffing it behind the wiring leaves an uninsulated void right where there is already a hole in the vapour barrier.
Can you insulate my finished walls without removing the drywall?: Not with batts — they need an open cavity. That is a job for a blown-in or injected product, or for adding insulation on the room side. We will tell you that rather than sell you a partial job.
Why is my Caernarvon basement cold along the floor edge?: Usually the rim joist. It is thin, directly exposed to outside, and in most basements it is bare or has a batt tucked loosely against it. It needs air sealing first, then insulating.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paint

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat). Confirm quantities before buying.

Rather we handle it? Get a free estimate →

Batt Insulation Caernarvon

Mineral wool and fibreglass batts in Caernarvon walls and ceilings