How do I know I got the depth I paid for?

We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

How much insulation should my Pleasantview attic have?

The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.

Can you just blow on top of what is already there?

Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.

Why does my Pleasantview attic frost up in winter?

Almost always warm moist air leaking up from the house through pot lights, top plates or the hatch, then condensing on cold sheathing. More insulation on its own does not fix it — the leaks have to be sealed first.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Attic Insulation Pleasantview | Attic Insulation

Blown-in attic insulation in Pleasantview, sealed before it is filled

The most common mistake in an Pleasantview attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Existing insulation levelled before the top-up
Attic hatch insulated and weatherstripped
Blown-in loose-fill to the depth your permit specifies
Air sealing at pot lights, top plates and the attic hatch
Baffles kept clear so the soffit vents still breathe
Depth markers left in place so the result is verifiable

The attic hatch, which everybody forgets

A hole in the ceiling

The hatch in an Pleasantview home is often an uninsulated panel sitting in a frame with no weatherstrip. It is a direct opening between the house and a space that is at outdoor temperature.

What we do

The hatch gets insulated on its back face and weatherstripped so it seals when closed. It is a small job that shows up disproportionately in comfort, and it is the first place we look when someone says the hallway is cold.

Pleasantview drywall in context

About Pleasantview

Close to Southgate Mall, the area's most prominent feature is its elevation: hence the name Pleasantview.

What we see in Pleasantview

In Pleasantview the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Depth, and how to check we delivered it

Verifiable rather than assumed

Blown insulation settles, and depth is easy to claim and hard to check once the hatch is closed. We leave depth markers through the Pleasantview attic so the installed depth can be read off later by anyone.

Even coverage

Depth is also an average — a deep drift in the middle and thin corners is not the same as an even blanket. Coverage to the edges is what actually reduces heat loss.

Insulating a Pleasantview attic with knob-and-tube or old wiring

Stop and check first

Some older Pleasantview homes still carry active knob-and-tube wiring in the attic. Burying it in insulation is not something we do — it needs an electrician to assess and usually to replace before the attic is filled.

Why we raise it

It is the kind of thing found halfway through a job, and it is far cheaper to find at the quote. If we see it, we tell you and we stop until it is dealt with.

Why air sealing comes before insulation in Pleasantview

Insulation does not stop air

Batt and loose-fill slow heat transfer; neither stops air movement. In an Pleasantview attic warm moist household air rises through pot lights, top plates and the hatch, passes straight through the insulation and condenses when it hits the cold deck.

What that looks like later

Frost on the underside of the sheathing in February, then staining on the ceiling in spring. Sealing the penetrations first is the difference between insulation that works and insulation that becomes the problem.

Keeping the eaves clear in an Pleasantview attic

Ventilation and insulation are not opposites

An attic needs air moving from the soffits up to the ridge. Blowing loose-fill right into the eaves blocks that path, and a blocked attic gets damp regardless of how much insulation is in it.

Baffles

Baffles hold the insulation back so the soffit vents stay open. In older Pleasantview homes they are often missing entirely, which is why the corners look thin — someone deliberately kept the insulation back, or it was never installed to the edge.

Topping up against removing and replacing

Usually a top-up is fine

Old fibreglass in an Pleasantview attic that is dry and undisturbed can be levelled and topped up. It still insulates, and removing it is a large cost for a small gain.

When it has to come out

Insulation that is wet, contaminated, or full of rodent activity gets removed rather than buried, because topping over it seals the problem in. We will tell you which of the two you have after looking, not before.

How it works

Simple, clean, on schedule — Attic Insulation in Pleasantview

Free quote

We come out to your Pleasantview property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Pleasantview starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Pleasantview. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Pleasantview home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Pleasantview. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Pleasantview trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Pleasantview.

Read our reviews on Google

FAQ — Attic Insulation Pleasantview

Attic Insulation Pleasantview: your questions answered

How do I know I got the depth I paid for?: We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
How much insulation should my Pleasantview attic have?: The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.
Can you just blow on top of what is already there?: Usually yes, if the existing insulation is dry, undisturbed and not contaminated. If it is wet or shows rodent activity it comes out first, because topping over that seals the problem in rather than fixing it.
Why does my Pleasantview attic frost up in winter?: Almost always warm moist air leaking up from the house through pot lights, top plates or the hatch, then condensing on cold sheathing. More insulation on its own does not fix it — the leaks have to be sealed first.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paint

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat). Confirm quantities before buying.

Rather we handle it? Get a free estimate →

Attic Insulation Pleasantview

Blown-in attic insulation in Pleasantview, sealed before it is filled